Revision 5 as of 2011-04-22 12:30:50

Clear message


Install Kubuntu on Archos 10.1 internet tablet

  • Install SDE firmware (see
  • Generate a kubuntu mobile img using rootstock

sudo rootstock --fqdn archos --login u --password u --keepimage --imagesize 1500M --seed kubuntu-mobile --
dist maverick
  • Mount the rootfs.img of the SDE from your data partition (that is the thing you can mount when doing the USB sharing dance with Android)
  • Mount your Kubuntu .img
  • copy /lib/modules/* from the former to the latter
  • Unmount both (best also run sudo sync)
  • Move the SDE rootfs.img out of the way
  • Copy your Kubuntu .img as new rootfs.img on the data partition
  • sudo sync; unmount and power off the device
  • Power on and hold volume down pressed until the recovery boot thing comes up
  • Select developer edition using the volume button and confirm using the power button
  • If all goes fine you should get to either KDM or TTY login
  • To power off again you'll need to reset by keeping the power button pressed for 10 seconds


The better part of ARM/n900 also applies for the Archos 10.1.

Install Software

Sames as n900 really. Mount the rootfs.img and chroot into it then do whatever modifications you deem necessary.

sudo apt-get install ssh

Once you have SSH you can do everything else over SSH and USB networking, see below.

USB Networking

  • In the device's /etc/network/interfaces

auto usb0
iface usb0 inet static
        pre-up rmmod musb_hdrc
        pre-up modprobe musb_hdrc mode_default=2
        pre-up modprobe g_ether
  • In the host's /etc/network/interfaces

auto usb0
iface usb0 inet static
        up iptables -A POSTROUTING -t nat -s -j MASQUERADE
        up echo 1 > /proc/sys/net/ipv4/ip_forward
        down iptables -D POSTROUTING -t nat -s -j MASQUERADE
        down echo 0 > /proc/sys/net/ipv4/ip_forward
  • If you wish, you can of course also pull udev magic as with the n900 as to not having to use usb0
  • After starting the device you should be able to connect to it at


sudo apt-get install xserver-xorg-video-omapfb xserver-xorg-input-tslib
  • xorg.conf:

Section "Module"
        Load          "extmod"
        Load          "dbe"
        Load          "glx"
        Load          "freetype"
        Load          "type1"
        Load          "record"
        Load          "dri"

Section "Monitor"
        Identifier      "Builtin Default Monitor"

Section "Device"
        Identifier      "Builtin Default fbdev Device 0"
        Driver          "omapfb"

Section "Screen"
        Identifier      "Builtin Default fbdev Screen 0"
        Device          "Builtin Default fbdev Device 0"
        Monitor         "Builtin Default Monitor"

Section "InputDevice"
        Identifier      "Touchscreen"
        Option          "DeviceName" "Touchscreen"
        Option          "Device" "/dev/input/by-id/usb-UNITEC_USB_Touch__Win7_-event-if00" 
        Option          "Emulate3Buttons" "false"
        Option          "SendCoreEvents" "On"
        Driver          "evdev"

Section "InputDevice"
        Identifier      "dummy"
        Driver          "void"
        Option           "Device" "/dev/input/mice"

Section "ServerLayout"
        Identifier      "Builtin Default Layout"
        Screen          "Builtin Default fbdev Screen 0"
        InputDevice     "Touchscreen" "CorePointer"
        InputDevice     "dummy"
  • tslib without evdev should technically also work, however it claims the device is no touchscreen, so maybe not Wink ;)

  • turning off 3 button emulation is essential to get some sort of sensible click behavior


Not yet working, will at least need kernel headers and sources present: ARM/OMAP/Graphics