|Deletions are marked like this.||Additions are marked like this.|
|Line 5:||Line 5:|
|In a terminal:||In a terminal (you will need the [wiki:AddingRepositoriesHowto universe repository enabled]):|
|Line 121:||Line 121:|
|I tried to omit any details or explanations I didn't think we're necessary to try to keep the size of this howto to a minimum but feel free to ask questions and post comments on the forums (a forum thread will be created shortly, once it has been created I will update this page with a link).||I tried to omit any details or explanations I didn't think we're necessary to try to keep the size of this howto to a minimum but feel free to ask questions and post comments on the forums in the folowing thread: http://ubuntuforums.org/showthread.php?t=97936.|
Enabling all of the functions on your Logitech MX1000 mouse
This guide will step you the process of enabling all 12 buttons on your logitech mx1000 mouse, including the side buttons, side scroll and cruise control (aka auto vertical scroll) functionality.
Install the necessary packages
In a terminal (you will need the [wiki:AddingRepositoriesHowto universe repository enabled]):
sudo apt-get install xvkbd xbindkeys xmacro
Set up evdev
Make sure your mouse is connected to a usb port, not the PS/2 port.
Get some info
- Now we need to get some information about the mouse. In a terminal:
cat /proc/bus/input/devicesIn my case the output was,
jason@luso:~$ cat /proc/bus/input/devices I: Bus=0011 Vendor=0001 Product=0001 Version=ab41 N: Name="AT Translated Set 2 keyboard" P: Phys=isa0060/serio0/input0 H: Handlers=kbd event0 B: EV=120013 B: KEY=1 80000004 2000000 3002078 f840d001 f2ffffdf ffefffff ffffffff fffffffe B: MSC=10 B: LED=7 *I: Bus=0003 Vendor=046d Product=c50e Version=2500 *N: Name="Logitech USB Receiver" *P: Phys=usb-0000:00:1d.0-1/input0 *H: Handlers=mouse0 event1 ts0 *B: EV=7 *B: KEY=ffff0000 0 0 0 0 0 0 0 0 *B: REL=143 I: Bus=0010 Vendor=001f Product=0001 Version=0100 N: Name="PC Speaker" P: Phys=isa0061/input0 H: Handlers=kbd event2 B: EV=40001 B: SND=6 jason@luso:~$We're interested in the section concerning the mouse (which is marked above by *'s). You're information may be different than mine so do not assume that you can just use the values displayed above. Specifically, we want three pieces of information. Make sure you write these down somewhere: Name, Phys, and Handlers.
- Now we need to actually use this information and edit xorg.conf. Let's make a backup and then open it up for editing. In a terminal:
sudo cp /etc/X11/xorg.conf /etc/X11/xorg.conf.backup sudo gedit /etc/X11/xorg.conf
- Find the section that looks like:
Section "InputDevice" Identifier "Configured Mouse" ... EndSectionGo ahead and delete this section (don't worry we made the backup in case anything goes wrong) and replace it with the following template:
Section "InputDevice" Identifier "Configured Mouse" Driver "mouse" Option "CorePointer" Option "Protocol" "evdev" Option "Dev Name" "Logitech USB Receiver" Option "Dev Phys" Option "Device" Option "Buttons" "12" Option "ZAxisMapping" "4 5 7 6" EndSection
- Now look at the piece of paper where you wrote down the information from before. If Name was the same as "Logitech USB Receiver", then you can leave the "Dev Name" line alone since it is the same as the template. If it is different, then change "Logitech USB Receiver" appropriately.
- Still with that piece of paper in your hand, look at what your Phys was. In the "Dev Phys" line in your xorg.conf file add the appropriate option. In my case I got Phys=usb-0000:00:1d.0-1/input0 and so I would add "usb-*/input0" (see below for a completed template). What matters here is the input[NUMBER] part, we can use a wildcard for the 0000:00:1d.0-1 part.
- The last piece of information we are going to use from your paper is Handlers. In my case, Handlers was "mouse0 event1 ts0". We only care about the event[NUMBER] part. In my case I would add "/dev/input/event1" to the "Device" line. If your Handlers had event0 in it, then you would add "/dev/input/event0", etc.
- The finished product should look similar to:
Section "InputDevice" Identifier "Configured Mouse" Driver "mouse" Option "CorePointer" Option "Protocol" "evdev" Option "Dev Name" "Logitech USB Receiver" Option "Dev Phys" "usb-*/input0" Option "Device" "/dev/input/event1" Option "Buttons" "12" Option "ZAxisMapping" "4 5 7 6" EndSection
Great we are done with editing xorg.conf. Double check to make sure you didn't make any typos because X may refuse to start if you did (if that happens just restore the backup copy of xorg.conf and start over: sudo rm /etc/X11/xorg.conf; sudo cp /etc/X11/xorg.conf.backup /etc/X11/xorg.conf). If everything looks okay go ahead and save your changes and exit. Okay almost done, that was the hard part.
- Restart X by pressing ctrl+alt+backspace (make sure you save anything you are working on).
- At this point your mouse should have side scroll and cruise control working. Go ahead and try it in firefox if you'd like. However, the side buttons won't go back and forward in your history and the cruise control will highlight text as it scrolls vertically. We are going to take care of those problems now.
- In a terminal:
- Paste the following into your new file:
"/usr/X11R6/bin/xvkbd -xsendevent -text "\[Alt_L]\[Left]"" b:8 "/usr/X11R6/bin/xvkbd -xsendevent -text "\[Alt_L]\[Right]"" b:9 "echo ButtonPress 4 ButtonRelease 4 | xmacroplay -d 0 :0.0" b:11 "echo ButtonPress 5 ButtonRelease 5 | xmacroplay -d 0 :0.0" b:12
- Save your changes and exit.
Add xbindkeys to your startup programs in the System -> Preferences -> Sessions -> Startup Programs
So that you don't have to reboot, you can just run xbindkeys in a terminal.
Try out all of the buttons on your mouse now. The side buttons should let you go back and forward in your history. And the side scroll and cruise control should be working perfectly. I haven't found a good use for that third side button but you can setup a bind for it with xbindkeys (it should be "b:10").
I tried to omit any details or explanations I didn't think we're necessary to try to keep the size of this howto to a minimum but feel free to ask questions and post comments on the forums in the folowing thread: http://ubuntuforums.org/showthread.php?t=97936.
I should note that most of the evdev setup was ripped from [http://ubuntuforums.org/showthread.php?t=65471 A complete guide to a Logitech mouse] by endy on the forums.