Differences between revisions 32 and 44 (spanning 12 versions)
Revision 32 as of 2005-11-13 21:44:47
Size: 7155
Editor: s64-186-37-120
Revision 44 as of 2006-06-19 16:06:34
Size: 59
Editor: 127
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
= Thin Client How-To =

== What is a Thin Client? ==

To the user, a thin client behaves like a regular desktop computer. To the administrator, a thin client has no storage of its own, is easy to maintain, and can give the user a modern computing experience even with ancient hardware.

== How do thin clients work? ==

-- Basic answer --

Thin clients load a small operating system into memory then connect to the server. The programs run on the server but are displayed on a thin client's screen.

-- Advanced answer --

Boot phase (described from the point of view of the thin client machine):
A thin client may either obtain a kernel from local storage, or load the kernel across the network. (Using these instructions, you will collect the linux kernel from the server using a bootable network card. This way, the thin client needs no more storage than the boot rom built into a bootable network card.)

- Boot sequence -

The PXE network card makes a DHCP request on the local network. The DHCP reply gives information to the card where to collect the linux kernel from. The kernel is collected over the network through the TFTP protocol.

Once the kernel has been collected via TFTP, the kernel is executed; the machine boots linux. A initramfs collected with the linux kernel is mounted as a root file system. This carries and autodetect the necessary drivers for the network card, mouse, keyboard sound etc. Once the network card driver is loaded, a second DHCP request tells the client it's ip address, netmask, gateway, DNS server, and root NFS (Network File System) mount point.

The linux kernel runs the ubuntu initramfs, which mounts the root NFS share from the server onto the thin client read-only. The thin client now has a booted linux kernel, and a root file system, much like any Linux system. From now on, when we talk of the root file system on the client, we are actually talking about a root file system mounted read-only from the server. The root file system mounted by the thin client is not the same root file system the server itself uses, but is specially prepared for thin clients, and is shared by all thin clients connected to the server (located in /opt/ltsp/<arch> on the server) . The initramfs calls the init program, the Xserver settings are autodetected and the ubuntu breezy ltsp login manager, called ldm is started.

- X nuts and bolts -

After logging in, ldm starts a ssh tunnel and executes a X session on the server which is displayed through the tunnel on the thin clients X server. Using ssh here has the big advantage that you dont need to have a Xserver configured on the client and no unsafe tcp X transport is initialized like it was done in older days of ltsp.

== Requirements ==

You will need:

 * An Ubuntu 5.10 system to be the server
 * At least one PXE-bootable system to be a client
 * A bunch of disk space
 * A fast network connection, or a local Breezy mirror, or some patience
 * A DHCP server which is capable of supporting PXE clients, or a separate network segment where you can run a dedicated DHCP server
 * Command-line familiarity
 * A sense of adventure
 * A burning desire to send feedback to [ ubuntu-devel]

== Getting Started ==

'''NOTE:''' If you plan to use the server as gateway/nat/firewall machine, it is strongly suggested to configure all the network interfaces before proceeding with the following steps.

 1. Set up the DHCP server
  * If you have an existing DHCP server which can support PXE clients:
   * Configure it to pass a boot filename of `/ltsp/pxelinux.0` and a root path of `/opt/ltsp/i386`
   * For ISC DHCPD, use the following options: {{{
filename "/ltsp/pxelinux.0";
option root-path "/opt/ltsp/i386";
   * Install `ltsp-server` on the server: {{{sudo apt-get install ltsp-server
  * If you want to run a dedicated DHCP server on the thin client server:
   1. Install `ltsp-server-standalone` on the server: {{{sudo apt-get install ltsp-server-standalone
   1. If necessary, customize `/etc/ltsp/dhcpd.conf` (by default it's configured for a server at serving PXE clients)
   1. If you are running a firewall on the server, you'll need to open TFTP and NFS (and DHCP if you're running the standalone server). Also, make sure portmap isn't limited to the loopback interface in /etc/default/portmap (comment out the line with "-i") if it exists, could be a leftover from Hoary. You also may want to edit `/etc/hosts.allow' and limit access for ''portmap'', ''rpc.mountd'', ''rpc.statd'', and ''in.tftpd'' to the local network: {{{portmap:
   1. Restart the nfs subsystem: {{{sudo invoke-rc.d nfs-kernel-server restart
sudo invoke-rc.d nfs-common restart
sudo invoke-rc.d portmap restart}}}
 1. Build the thin client runtime environment: {{{sudo ltsp-build-client
  * This script is hardcoded to use a particular Ubuntu mirror, so you may wish to edit it if you have a nearby mirror or CD (sudo ltsp-build-client --mirror file:///cdrom), remember to copy sources.list from the server into the chroot)
  * If you changed your aptitude dependency-settings not to select recommended packages automatically, not all required packages will be downloaded and installed by this script. Then no login with sdm is possible for example because some parts of the x-server are missing
 1. {{{apt-get install openssh-server
sudo ltsp-update-sshkeys}}} Check `/opt/ltsp/i386/etc/ssh/ssh_known_hosts` and ensure that your host key is associated with your host's IP address. Depending on your `/etc/hosts` configuration, this may not always be correct automatically (yet). If it looks like this: {{{
servername ssh-rsa AAAAB3NzaC1yc2EAAAABI...
}}} then add the IP address like this: {{{
servername, ssh-rsa AAAAB3NzaC1yc2EAAAABI...
}}} AND file a bug in [ Bugzilla]. THIS SHOULD NOT HAPPEN.
 1. {{{sudo invoke-rc.d dhcp3-server start
 1. Optionally, create `/opt/ltsp/i386/etc/lts.conf`. If you don't create one, reasonable defaults and auto-detected values will be used.
 1. PXE boot the client and see what happens. If all goes well, you should see a graphical login dialog.
 1. If your client doesn't have PXE on the network card, you can generate a custom boot CD or floppy at []. Burn the iso or floppy image and boot from that.
 1. Log in, with any user authorized to login remotely via ssh, and see what happens. If all goes well, you should get a working desktop session on the server.
 1. Send mail to [ ubuntu-devel] with your findings

=== Tips ===
If you have a separte DHCP that you do '''not''' want to install LTSP on you can just redirect the thin-client to boot off a different server.

In your DHCP server's dhcpd.conf:
}}} where is the address of your LTSP server

=== Extras ===

 1. ["ThinClientHowtoNAT"]

ThinClientHowto (last edited 2008-08-06 16:14:39 by localhost)