Diff for "SergioZanchetta/Old/ToshibaTecraM2"

ToshibaTecraM2

Differences between revisions 9 and 10

dmesg output informs me that I have to turn off the killswitch to run wireless but setup insists on having the killswitch turned on
Does not associate with AP
1024x768 resolution is unstable; screen is fuzzy. Switching from another resolution works, but going back getting a clear 1024 seems to be a hit or miss issue.

It is a struggle to run Breezy on this unit; I've burned and tested at least 5 Colony 3 CDs as well as the daily build (08222005) and I still get consistent failures on installing at Stage 2 (tty4 shows its trying to install some OOo and Mozilla packs)
Won't reboot after Stage 1 of installation, had to pull out battery [http://bugzilla.ubuntu.com/show_bug.cgi?id=13882 #13882]
Won't reboot after doing sudo shutdown -r now, had to pull out battery [http://bugzilla.ubuntu.com/show_bug.cgi?id=13882 #13882]
Fan doesn't seem to work (uh-oh) - runs on Hoary though

Hardware Information
Screen & Monitors
Device	Works?		Bug #
Device	in Hoary (current stable)?	in Breezy (current development)?	Bug #
Screen	Untested	Yes
Correct resolution?	No, 1024x768 is fuzzy; only 800x600 is usable	Yes, at 1024x768
Correct refresh rate?	Yes	Yes
3D Acceleration	Untested	Untested
External monitor works?	Untested	Untested
External monitor - mirrors	Untested	Untested
External monitor - extend desktop	Untested	Untested
Power Management
Battery detected?	Yes	Yes
Hibernates?	Yes	Yes
Sleep	Untested	No
Dim/Blank monitor?	No	No
Sound
Sound works?	Yes	Yes
Correct volume?	Yes	Yes
Hardware volume switch	Yes	Yes
Headphone jack	Yes	Yes
Mic jack	Untested	Untested
Networking
Wired NIC	Yes	Yes
Wireless NIC	No	No
PCMCIA NIC	Untested	Untested
Firewire	Untested	Untested
Bluetooth	Untested	Untested
Modem	No	No
Infrared	Untested	Untested
Touchpad & Mice
Accupoint	Yes	Yes
Touchpad	Yes	Yes
Touchpad - Doubletap = double click	Yes	Yes
Touchpad - Scroll down side	No	No
External mouse - USB	Yes	Yes, but scroll doesn't work, when pulled out, dual pointing device doesn't work
External mouse - Serial	Untested	Untested
Docking Station/Port Replicator
AC through replicator	Untested	Untested
USB	Untested	Untested
Serial	Untested	Untested
Parallel	Untested	Untested
External Monitor - VGA	Untested	Untested
External Monitor - DVI	Untested	Untested
Modem	Untested	Untested
NIC	Untested	Untested
PS/2	Untested	Untested
Additional Hardware
Fingerprint reader	N/A	N/A
CD/DVD drive	Yes	Yes
PCMCIA cards	Untested	Untested
SC Card Reader	Untested	Untested

Function and other keys
Fn key	Operation	Keycode	Works?		Bug #
Fn key	Operation	Keycode	in Hoary (current stable)?	in Breezy (current development)?	Bug #
+ Space	Cycle through screen resolutions		No	No
+ Esc	Turns soundon or off		No	No
+ F1	Blanks the display		No	No
+ F2	Changes the Power Save Mode		No	No
+ F3	Standby mode		No	No
+ F4	Hibernation mode		Yes, beeps 4 times, then shows XScreensaver login	Yes, shows a Grey screen, beeps 4 times then shows XScreensaver login
+ F5	Changes the active display device		Yes, but cannot return to original state unless resolution is changed	Yes, but cannot return to original state, dual pointing device won't work anymore
+ F6	Decreases the display brightness		Yes	Yes
+ F7	Increases the display brightness		Yes	Yes
+ F8	Enables or disables WLAN or Bluetooth		No	No
+ F9	Enables or disables Touch pad function		No	No
+ F10	Turns the cursor control overlay on or off		Untested	Untested
+ F11	Turns the numeric overlay on or off		Untested	Untested
+ F12	Turns the text scrolling on or off		No	No
+ 1	Toshiba Zoom Utility - Reduce		No	No
+ 2	Toshiba Zoom Utility - Enlarge		No	No
Other special keys
Key	Operation	Keycode	Works?		Bug #
Key	Operation	Keycode	in Hoary (current stable)?	in Breezy (current development)?	Bug #
Key			Untested	Untested

SergioZanchetta/Old/ToshibaTecraM2 (last edited 2010-02-26 15:29:47 by host226-241-dynamic)

-  ⇤ ← Revision 9 as of 2005-08-23 02:41:14 → 
  Size: 5779
  Editor: adsl-57
  Comment:
+   ← Revision 10 as of 2005-08-23 02:46:55 → ⇥
  Size: 5777
  Editor: adsl-57
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 31:
- * ''dmesg'' output informs me that I have to turn off the killswitch to run wireless but setup insists on having the killswitch turned on
+ * `dmesg` output informs me that I have to turn off the killswitch to run wireless but setup insists on having the killswitch turned on